CAN to Ethernet Converter(BUE-CANET-I & BUE-CANET-II)
1.1 Product Overview
Our CAN to Ethernet(TCP/IP) converter is an intelligent CAN bus communication interface that is compatible with TCP/IP protocol and supports one or two CAN channel. Using this module will enable PC to connect to CAN-bus network via USB bus, forming the CAN-bus network control nodes for the data processing and data collection for the CAN-bus networks such as bus laboratory, industrial control, intelligent residential zone, auto electronics network, and etc.
CAN to Ethernet gateway comes with an electrical isolation module, which could be used to avoid the damage caused by the ground loop and enhance the system reliability when working under a tough environment.
Our CAN to Ethernet converter can use our Tester software provided by us to directly finish CAN Bus message sending, and receiving.
1.2 Parameters
- Application as Ethernet based interface to the CAN bus Microcontroller STR912FAW44X6(ARM9 Based) Ethernet 10M/100M
- Baud rates up to 1MB & 7500 frames.
- CAN 2.0A (11-bit ID standard frames) and 2.0B (29-bit ID extended frames) Config software available through the Ethernet interface.
- Comply with ISO-11898.
- Examples of Visual C++, C++Builder are available; Max data flow 6000PS (extend frame)
- Operating temperature: -20 to +70
- Physical size: (length) 105mm * (width) 84mm * (height) 28mm. Powered by DC (7 to 40V)
- Can Bus port number: 1 or 2
1.3 Typical applications
- CAN-bus network diagnosis and test
- Auto electronic applications
- Electric power communication network
- Industrial control devices
- High-speed and large data communications
Ordering Information:
|
Model Number |
Description |
Port No. |
Fiber Mode |
Fiber Connector |
|
HFD-FO-CAN-P1M |
Fiber Optic Converter,Point to Point Link, Single Fiber(BI-DI), 2km,DIN Rail Mount |
1 CAN +1 FO |
Multi Mode |
ST/SC/FC |
|
HFD-FO-CAN-P2M |
Fiber Optic Converter,Point to Point Link, Dual Fiber, 2km,DIN Rail Mount |
1 CAN+1TX+1RX |
Multi Mode |
ST/SC/FC |
|
HFD-FO-CAN-P1S |
Fiber Optic Converter,Point to Point Link, Single Fiber(BI-DI), 20km |
1 CAN +1 FO |
Single Mode |
ST/SC/FC |
|
HFD-FO-CAN-P2S |
Fiber Optic Converter,Point to Point Link, Dual Fiber, 20km |
1 CAN+1TX+1RX |
Single Mode |
ST/SC/FC |
|
FO-FIB-100PT |
Configurable Fiber Optic Converter, Point to Point Link,Wall Mount |
1CAN+1TX+1RX |
Single Mode |
ST/SC/FC |
|
FO-FIB-100BT |
Configurable Fiber Optic Converter, Multi Drop Link,Wall Mount |
1CAN+2TX+2RX |
Single Mode |
ST/SC/FC |
|
FO-FIB-MIXED |
Configurable CAN Fiber Optic Switch, Point to point,Multi-drop,Star,Tree, Wall Mount |
2CAN+FO(2TX+2RX) |
Single Mode |
ST/SC/FC |
|
SW-400T |
4 Port Configurable CAN BUS Switch, Wall Mount |
4 CAN |
||
|
BRIGE-200T |
Configurable CAN TO CAN Bridge |
2 CAN |
||
|
CANET-I |
1 Port CAN to Ethernet Converter |
1 CAN+1 TCP |
||
|
CANET-II |
2 Port CAN to Ethernet Converter |
2 CAN+1 TCP |
||
|
CAN-USB-I |
1 Port CAN to USB Converter |
1 CAN+1 USB |
||
|
CAN-USB-II |
2 Port CAN to USB Converter |
2 CAN+1 USB |
||
|
CAN-PCI-5001 |
1 Port CAN PCI Card |
1 CAN+1 PCI |
||
|
CAN-PCI-5002 |
2 Port CAN PCI Card |
2 CAN+1 PCI |
||
|
CAN-232 |
CAN to RS-232 Converter |
1 CAN+1RS232 |
||
|
CAN-485 |
CAN to RS-485 Converter |
1 CAN+1RS485 |